LD800RC Bucket Tooth Operation Manual
1. Product Overview
1. Model: LD800RC Bucket Tooth (Rock Chisel Tip)
2. Material: Alloy structural steel, quenched and tempered by heat treatment
3. Hardness: HRC48~54 at tooth tip, balancing wear resistance and impact toughness
4. Application Conditions: Mining, quarrying, rock excavation, hard soil and weathered rock. The RC chisel tip is designed for priority rock penetration.
5. Matching Parts: Compatible with corresponding tooth adapter, bucket tooth pin and retaining ring.
6. Applicable Machine: 80-ton class large excavators (equivalent models such as CAT 390)
2. Bucket Tooth Installation Instructions
⚠️ Safety Precondition: Lower the excavator bucket to the ground, shut down and cut off power to prevent unexpected movement.
1. Clean the inner cavity of the tooth adapter, remove sediment, rust and residual old pins. Inspect the wear condition of the tooth adapter. If the wear clearance of the tooth adapter is excessive, it shall be replaced simultaneously; otherwise, tooth breakage is highly likely to occur.
2. Align the LD800RC bucket tooth with the tooth adapter and push it fully into place.
3. Align the pin holes, install the bucket tooth pin, and fit the retaining ring to lock and position.
4. Strike to confirm the pin is fully seated and the retaining ring is completely clipped into the slot without looseness.
5. After installation, shake the bucket tooth by hand to check for free play. Test the bucket movement with no load to ensure no interference.
Replacement Suggestion: Replace bucket tooth pins and retaining rings with new ones during disassembly and assembly. Old parts are prone to fatigue fracture.
3. Operation Specifications (Key to Extend Service Life)
1. Digging Angle: Keep bucket teeth perpendicular to the working surface during excavation as much as possible. Avoid prying at a large oblique angle; eccentric load will easily cause fracture at the tooth root.
2. No Heavy Load Swing: Do not swing the stick left and right to tear forcibly after the bucket bites rock. Lateral impact force will directly break the bucket tooth.
3. No Bucket Dropping: Do not drop the bucket from height onto rocks. Severe impact will cause invisible cracks and sudden breakage of bucket teeth.
4. Digging Motion: Lower the bucket for penetration before curling the bucket. Do not curl the bucket forcibly while lifting the boom to pull the bucket tooth.
5. Wear Position Adjustment: Outer bucket teeth of the bucket wear faster. Regularly swap inner and outer bucket teeth to balance wear.
4. Daily Inspection and Maintenance
1. Pre-shift Daily Inspection
• Visual check: Check bucket teeth for cracks and chipped tips.
• Check whether bucket tooth pins and retaining rings are loose or disengaged.
• Inspect wear of tooth adapters.
2. Excavator Bucket Teeth Replacement Criteria
• Replacement is recommended when the remaining height of worn tooth tip is more than 1/3. When worn down to the root, digging resistance increases and fuel consumption rises.
• Stop the machine immediately for replacement if bucket teeth have cracks or chipping, to prevent bucket teeth from falling into mineral materials.
• Replace the tooth adapter when its wear exceeds 10%. Otherwise, new bucket teeth will break easily.
3. Storage: Store spare bucket teeth indoors to avoid moisture, rust and bumps that cause internal damage.
5. Skid Steer Bucket Teeth
Safety Warnings
1. Wear safety helmet, safety goggles and protective gloves during disassembly and assembly. Prevent flying fragments when striking parts.
2. Never work under a suspended bucket.
3. Bucket teeth are wearing parts. Normal wear is not covered by warranty. Breakage caused by improper operation (prying, dropping, swinging arm) is not a product quality problem.
4. If bucket teeth fall off during operation, stop the machine in time to retrieve them to avoid serious damage to crushers.
6. Simple Fault Diagnosis
1. Frequent bucket tooth fracture: Mostly caused by excessive wear clearance of tooth adapter, improper digging angle or heavy impact from large hard rock blocks.
2. Pins tend to slip out: Retaining ring not fitted in place or pin hole wear.
3. Excessively fast wear: High abrasive working condition or continuous oblique digging operation.