Huizhou Antenk Electronics Co Ltd manufactures two position screw lock power connector for steady power circuit connection inside various electronic devices. This two pole power connector adopts reliable screw locking structure to hold wire firmly without soldering operation, official engineering drawing provides complete outline dimension and general tolerance data for mechanical design reference, linear tolerance follows plus minus zero point zero five millimeter and angular tolerance follows plus minus zero point two five degree as drawing requirement. Users strip wire end and fasten screws to clamp conductors for stable power transmission, no extra soldering work is required for on site installation. Operators should strictly follow drawing tolerance values during casing design apply proper torque for screw tightening to avoid thread damage and store finished goods in dry clean area to prevent metal component corrosion. Unlike competitors purchasing finished assemblies from outside suppliers Antenk carries out full in house workflow covering mold development metal stamping plastic molding assembly and comprehensive laboratory performance inspection. Our factory holds ISO9001 ISO14001 IATF16949 and UL certifications and more than seventy percent finished goods export worldwide. This power connector fits industrial control instruments digital household appliances power supply modules and precision instrument products. Please share your mounting requirement and project specifications for free sample evaluation and complete technical drawing support.
Screw Lock Power Connector delivers stable wire clamping performance for reliable power circuit interconnection in electronic equipment.
Vibration Resistant Power Plug maintains firm electrical contact even under continuous mechanical vibration during equipment operation.
Field Installable Power Connector enables convenient on site wiring without additional soldering procedures for various project deployments.
2.Detailed Specifications of Two Position Screw Lock Power Connector
1. Mechanical Specifications
1.1 Product type: Two position screw lock power connector
1.2 Measurement unit: millimeter
1.3 Key dimension: Refer to official engineering drawing for complete outline dimensions. General linear tolerance is ±0.05 millimeter, angular tolerance is ±0.25. Follow drawing tolerance requirements for housing and mechanical structure design.
1.4 Assembly method: Strip wire insulation, place conductors inside connector position and tighten screws to clamp wires for reliable power circuit connection. Soldering is not required for this assembly operation.
1.5 Ordering feature: Customizable mechanical dimensions can be supported to satisfy different equipment installation requirements.
1.6 CTA: Contact our engineering team to obtain complete dimension drawings and ordering specifications for your hardware design validation.
2. Material Construction
2.1 Housing and conductive component material: Refer to official engineering drawing for detailed material and surface finishing information.
3. Electrical & Environmental Performance Parameters
3.1 Electrical parameter: See official engineering drawing for rated current and rated voltage data.
3.2 Environmental compliance: Products comply with RoHS and REACH requirements.
4. Usage Method
4.1 Assembly mode: Strip wire insulation, insert wire conductors and apply proper torque to fastening screws to secure electrical connection.
4.2 Operation tip: Use dimension and tolerance values specified on engineering drawing for equipment structural design.
5. Application Scenarios
5.1 Power circuit connection for industrial control instruments
5.2 Internal power interconnection for digital household appliances
5.3 Power connection parts for power supply modules
5.4 Circuit connection for precision instrument products
6. Operation & Storage Precautions
6.1 Observe drawing linear and angular tolerances for related mechanical housing design
6.2 Apply appropriate torque when tightening screws to avoid thread damage or insufficient wire clamping force
6.3 Prevent scratches di rt and mechanical impact on connector before installation
6.4 Store products in dry clean environment to avoid corrosion of metal components
6.5 Confirm installation dimension requirements before placing purchase orders
6.6 CTA: Submit your hardware requirement mounting condition and project information, we provide free sample evaluation and professional technical consultation services.
3.FAQ
Q: How many packaging do you have?
A: We have five packages including PE bag, hand bag, zip lock bag, colorful box and white box currently.
Q: Can you do our own packaging?
A: Yes, you just provide the package design and we will produce what you want. We also have the professional designer can help you do the packaging design.
Q: How many different types of products your company manufactures?
A: Now we have more than 1,000 products. We have a strong advantage of OEM, just give us the actual products or your idea that you want, we will manufacture for you.
4.Product Drawing
